The Ultra SS Bullet Spike is designed for use with the Ultra SS V2 for those with deep thick carpet. Do keep in mind that’s it’s difficult to tune the alignment of a loudspeaker within a 1/16” once the spikes have been fitted! Sold singly.

The Ultra Base can be connected to the Ultra SS V2, Ultra II V2, Ultra 5 V2, and directly to any component in a system. One 1/4-20 x 5/8″ set screw is included with each Ultra Base. The 1/4-20 adapter listed below allows connection of the Ultra Base to the beveled lower section of the Ultra 5. The added height will provide more ventilation space under an amplifier if needed. The Ultra Base can also spread the mass of whatever is being supported over a larger area adding stability in some applications. Adding the Ultra Base to any Stillpoint can increase the performance of that Stillpoint significantly. Sold singly.

The Ultra 5 Bullet Spike is designed for use with the Ultra 5 V2 for those with deep thick carpet. Do keep in mind that’s it’s difficult to tune the alignment of a loudspeaker within a 1/16” once the spikes have been fitted! Sold singly.

The Ultra 5 V2 isolation feet approach the higher end of performance achieved by any Stillpoints products. Designed for use with components or floorstanding speakers, the Ultra 5 V2 contains four "technology pockets" in each unit and can be used without the Ultra Base on a perfectly level floor. The beveled base aids the adjustment of speakers once they have been fitted. Sold singly.

The Ultra 6 V2 are Stillpoints' flagship isolation feet for components (not designed for use with floorstanding speakers), containing multiple "technology pockets" to dissipate mechanical vibrations from your equipment and allow it to achieve its full potential. The Ultra 6 V2 is available with the Ultra Base if not being used directly on a Stillpoints ESS rack or component stand.

The Ultra 7 V2 are the flagship isolation feet, representing the pinnacle of performance that can be achieved by any Stillpoints product designed to isolate floorstanding speakers. These isolation feet are available to the public after being developed with the manufacturers of high-end loudspeakers, and do not require the use of any Ultra Base or Ultra Bullets.

The Components Stand SS is an upgraded version of the original Components Stand, and is 10 years in the making. It is designed so that Stillpoints fitted to the rack come into direct contact with your equipment, meaning they are better able to deal with the mechanical vibrations created by it.

Please note: this product DOES NOT come with any isolation feet included - instead, there is an Ultra Base supplied with each leg. You will need to order any desired isolation feet separately.

The Rail Grid was designed by Stillpoints to offer an improvement upon the existing Acrylic Shelf and X Grid - offering greater isolation than the acrylic version and far greater flexibility than the X Grid - the two Stillpoints fitted on each rail can be adjusted along the entire length of the rail, and the Rail Grid can easily replace any existing ESS Rack shelves. Isolation feet NOT included.

The Stillpoints ESS Rack is Stillpoints solution to rack isolation, and is fully configurable. You are able to select your desired height, width, number of shelves and then are also different options for the shelves themselves. Stillpoints isolation feet and Rail Grids must be ordered separately.

The original MiG or Mechanical Interface Ground is a superb footer that excels with a warm natural balance that can be tuned through two placement options to best match your system. Placing just one or two sets of MiG’s under your components can deliver a significant increase in sound staging with a balanced to slightly warm tonal balance.

MiG SX footers are an evolution of SR's original MiG footers developed in 2008. They started with a new specially tuned MiG resonator forged from high carbon steel and add a precision-machined Aircraft Aluminum and Carbon Fibre three-piece chassis engineered to distribute vibration through a special tuning disc and a UEF tuning element into Carbon Tungston ball bearings. For a bespoke match to your system, MiG SX has two placement options that re-tunes your component’s resonance; choose between Ambient and Pin-Point configurations and pick the option that best suits your system on a component by component basis.

Introducing Tranquility Base Carbon, the first all-new Tranquility Base in over a decade. SR started with a new chassis machined from a solid billet of aircraft aluminum for a 50% slimmer and 80% more rigid chassis. They then experimented with new laminates and arrived at carbon fiber for its superior response to mechanical and airborne vibrations. They then applied our most advanced EM Cell technology directly transferred from our Galileo SX PowerCell. Finally, its internal UEF Technology was transferred from our new state-of-the-art SRX cable loom. The net result is a thinner and more rigid Tranquility Base with a lower noise floor from which springs improved dynamics and soundstaging combined with smoother, more extended high frequencies.