Turntable Accessories
Cartridges, record cleaning, alignment tools, maintenance and covers from Hana, Ortofon, Pro-Ject, Record Doctor and Soundsmith.
Shop by Brand
-
£269.00Inc. VATThe Ortofon MC X10 is a moving coil cartridge featuring high-purity silver coils, a tipped elliptical diamond stylus, a MIM-moulded honeycomb stainless-steel body, and a newly developed optimised magnet system, offering an accessible entry into moving coil performance.
-
£499.17Ex. VATThe Ortofon MC X30 is a moving coil cartridge featuring a nude fine-line diamond stylus, high-purity silver coils, a MIM-moulded honeycomb stainless-steel body, and an optimised magnet system, delivering precise resolution and refined detail from vinyl.
-
£1,082.50Ex. VATThe Ortofon MC X50 is a moving coil cartridge featuring a nude Micro Ridge diamond stylus on a boron cantilever, high-purity silver quad coils, a MIM-moulded honeycomb stainless-steel body, and a newly formulated rubber suspension engineered specifically for the model.
-
£49.96Ex. VATThe AudioQuest HL-5 is a set of four tonearm headshell leads designed to replace stock cables in a turntable or headshell setup, bringing AudioQuest build quality directly into the analogue signal path.
-
£45.83Ex. VAT
The Ortofon Premium Libelle is a precision spirit level for turntables, offering a full 360-degree view with 1-degree accuracy, crafted from anodised aluminium with a wave-pattern grip surface and individually tested for measurement consistency.
-
From£162.50Ex. VATThe Little Fwend is a 100% mechanical automatic tonearm lifter that raises your stylus safely at the end of a record. Precision-machined in Scandinavia and hand-assembled in Oslo. Four models covering most turntable brands.
-
£374.17Ex. VATThe Pro-Ject VC-S3 is a premium vacuum record cleaning machine that wet cleans a 12 inch record and vacuums it dry in one to two revolutions. A magnetic clamp seals the label while the motorised platter turns at 30rpm beneath a vacuum arm, and the supplied Wash it 2 fluid is non-alcoholic so it will not damage the fine detail held in the groove. It also removes static, and holds 2.5 litres of waste fluid.
-
£833.33Ex. VATThe Gold Note B-5.2 is a 9 inch ball bearing tonearm designed and handmade in Italy, built to extract maximum detail from the vinyl groove with cartridges up to 15g. Four sealed micro ball bearings custom-made in Germany by GRW enable noiseless tracking, while a machined 6000 series aluminium arm wand provides the rigidity needed for accurate retrieval. Its 242mm effective length and 19mm overhang make it straightforward to fit to any high-end turntable.
-
£2,216.67Ex. VATThe Furutech LP Flattener DF-2 removes warps from vinyl records using a controlled heating and cooling cycle. Lay it flat, open it, place the record on the guides, close it and press one button; an LCD reports progress throughout. The heating plate reaches a maximum of 57°C, and the unit stores vertically to save space. UK model runs on 230V, drawing up to 460W.
-
£154.17Ex. VATThe Furutech ASB-1 is an antistatic brush for records, CDs and DVDs, built with COREBRID B core-sheath conductive fibres developed by Mitsubishi Chemical. Rather than attracting static onto the bristle surface, where it can discharge back onto the disc, the fibres conduct it away through a carbon core to ground, lifting dust from LP grooves in the same sweep.
-
£483.33Ex. VATThe Furutech Monza LP Stabilizer is a record weight built from precision-machined non-magnetic stainless steel base and top modules, girdled by a layer of damping carbon fibre. Its underside carries 16 concentric cushioning grooves formed from piezoelectric damping material, coupling the record to the platter while absorbing resonance. Weighs 350g.
-
£291.67Ex. VATThe Furutech La Source 101 is a set of four headshell lead wires built around pure silver Alpha conductors, seven strands of 0.16mm wire in Teflon insulation. The contact pins are machined from solid phosphor bronze and rhodium plated, with a four-way split tip for stable contact, and are crimped rather than soldered to the conductor. Fits standard 1.0mm cartridge and headshell pins.